








                           Information for SiS Users

                      Xavier Ducoin (xavier@rd.lectra.fr)

                                27 February 1998



1.  Introduction

This driver was primarily written for the SiS86c201.  It also works on the 202
, 205 and 5597/5598 chips. Support for 6326 is currently enabled, but tested
only on few cards.  Some support for SiS86c215 and 225 was added as well. This
support consists simply in identify it as 205, so probably 86c215 won't work
with acceleration (is a cheap 205 without some features).

The driver supports many advanced features.  These include:

   o Linear Addressing

   o 8/15/16/24 bits per pixel

   o Fully programmable clocks are supported

   o H/W cursor support

   o BitBLT acceleration of many operations

   o XAA support (XFree86 Acceleration Architecture)


2.  Supported chips

      SiS 86c201
            (External hardware clock)

      SiS 86c202, SiS 86c2x5, SiS 5597/5598, SiS 6326
            (Internal clock synthesizer)

Color expansion is not supported by the engine in 16M-color graphic mode.


3.  XF86Config Options

The following options are of particular interest for the SiS driver. Each of
them must be specified in the `svga' driver section of the XF86Config file,
within the Screen subsections of the depths to which they are applicable (you
can enable options for all depths by specifying them in the Device section).

      Option "set_mclk"
            This option lets you to modify the memory clocking of your card.
            (only for 5597 and 6326) Modifying the memory timings can destroy


 Information for SiS Users                                                    1





 Information for SiS Users                                                    2



            the device, but usually the only ill effects of overclocking is to
            have some noise an drawing errors, but BE CAREFUL. Usually a little
            increment can improve the drawing speed, and allows also higher
            dotclocks.  The server reports default memclock on starting mes-
            sages, so take it as a base. Units are in MHZ.

      Option "dac_speed"
            This option lets you to modify the maximum allowed dotclock (only
            for 5597 and 6326).     Without it, the server makes a conservative
            guess based on memory clock, speed and number of banks. If your
            monitor supports higher dotclocks and you know that your card can
            do it, give a try. If the speed is too high for your configuration
            (but not for your monitor), the effects can vary from some noise on
            screen to a black screen. Don't use speeds greater than 135 Mhz,
            (175 for 6326), even if your monitor supports the dot-clock.

      Option "noaccel"
            By default the XAA (XFree86 Acceleration Architecture) is used.
            This option will disable the use of the XAA and will enable the old
            BitBlt acceleration operations. (see below).

      Option "hw_clocks"
            On chips 86c202 and later, the default is to use the programmable
            clock for all clocks. It is possible to use the fixed clocks sup-
            ported by the chip instead of using this option (manufacturer
            dependent).

      Option "sw_cursor", "hw_cursor"
            The default is for using the hardware cursor.

      Option "no_linear"
            By default linear addressing is used on all chips.  However this
            might be broken in some implementations. It is possible to turn the
            linear addressing off with this option.  Note that H/W acceleration
            and 16/24bpp are only supported with linear addressing.

      Option "no_bitblt"
            This option will disable the use of all the BitBLT engine.  It is
            useful for problems related to acceleration problems.  In general
            this will result in a reduced performance.

      Option "no_imageblt"
            It is useful for problems related to image writing, and possible
            stipple acceleration problems. In general this will result in a
            reduced performance.

      Option "ext_eng_queue"
            5597/8 and 6326 have the option to extend the engine command queue
            on VRAM. With extended queue length, the driver only checks queue
            status on some color-expansion commands. This gives some perfor-
            mance improvement, but is possible to lose some commands, corrupt-
            ing screen output. As the size of extended command queue is 16-32K,
            the probability is very low, but exists. The performance gain
            observed is around 8-10%. Currently, using this option with








 Information for SiS Users                                                    3



            xaa_benchmark freezes the acceleration engine, causing weird image
            display.

      Option "pci_burst_on"
            This set a bit on some registers. Although documented, the utility
            of this option is unknown for me. I can't see any difference on
            stability or performance.

      Option "fast_vram"
            Enables 1 cycle memory access. Try it. Increased memory bandwidth
            reduces the possibility of glitches and noise on high resolution
            modes.

      Option "fifo_moderate","fifo_conservative","fifo_aggressive"
            These options modify the arbitration thresholds on CRT FIFO.
            Fifo_aggressive gives more time to CPU for accessing the VRAM.
            Fifo_conservative reduces the possibility of noise caused when the
            CRT tries to read memory when it is used by CPU, but reduces per-
            formance. The default is between aggressive and moderate (more
            aggressive than moderate).


4.  Modelines

When constructing a modeline for use with the Sis driver you'll need to con-
sider several points:

   o H/W Acceleration.  The H/W cursor, and fill operations currently allocate
     memory of the video ram for there own use.  If this is not available these
     functions will automatically be disabled. Also, ext_eng_queue allocate 32k
     of Vram.

   o Dot Clock. SiS documents the following video modes to work with 6326. The
     max dot clock allowable for your 6326 based board depends also on the mem-
     ory installed on it. Option fast_vram can be needed for high dot clocks to
     work. Of course, the memory installed must allow 1 cycle R/W. The server
     tries to avoid problems with high dotclocks, limiting the maximum based on
     estimated memory bandwidth.  Overriding the limits with dac_speed and mod-
     elines can damage the card if you exceed the card limits. Values between
     driver guess and chipset limits are acceptable, but can cause bad image
     quality, noise or no image displayed.

        o SiS recommended video modes for 6326:

        o    640x480  : 4, 8, 15, 16, 24 bpp at 85Hz Non-interlaced

        o    800x600  : 4, 8, 15, 16, 24 bpp at 85Hz Non-interlaced

        o   1024x768  : 4, 8, 15, 16, 24 bpp at 85Hz Non-interlaced

        o  1280x1024  : 4, 8, 15, 16, 24 bpp at 75Hz Non-interlaced

        o  1600x1200  : 4, 8  bpp at 65Hz Non-interlaced









 Information for SiS Users                                                    4



5.  Troubleshooting

The generic VGA driver doesn't work with 6326, so XF86Setup can't be used for
this card. Please use xf86config instead.

With intensive generation there is a snow phenomenon on the screen.  Can't
remove it even if I used the fifo low/high water mark dumped from W95.

The latter point is changed. Now we use calculated values for the fifo set-
tings, and this appears to be stable until the bandwidth required for CRT is
near the memory bandwidth (dotclock*depth/8 near Mclk*32 or Mclk*64 ).  In that
case, you could try to use fifo_moderate, fifo_conservative or a lower dot-
clock.

Some video modes with high dot-clocks don't work at all, resulting on black
screen. We are tracing now this problem. Lowering dotclock in that case could
solve the problem.

     Updated October 12, 1998 by Juanjo Santamarta, covering changes for 5597 and 6326.
     Updated November 6, 1998 by Juanjo Santamarta, covering changes for 5597, 86c2x5 and 6326.

     Generated from XFree86: xc/programs/Xserver/hw/xfree86/doc/sgml/SiS.sgml,v 3.3.2.6 1998/12/29 07:54:30 hohndel Exp $








































 Information for SiS Users                                                    5





































































                                   CONTENTS



1. Introduction  ............................................................ 1

2. Supported chips  ......................................................... 1

3. XF86Config Options  ...................................................... 1

4. Modelines  ............................................................... 3

5. Troubleshooting  ......................................................... 4











































                                       i



$XFree86: xc/programs/Xserver/hw/xfree86/doc/README.SiS,v 3.5.2.7 1998/12/29 08:00:10 hohndel Exp $
